c5471evm

README
^^^^^^

Toolchain
^^^^^^^^^

  A GNU GCC-based toolchain is assumed.  The PATH environment variable should
  be modified to point to the correct path to the SH toolchain (if
  different from the default).

  If you have no ARM toolchain, one can be downloaded from the NuttX
  Bitbucket download site (https://bitbucket.org/nuttx/buildroot/downloads/).

  1. You must have already configured NuttX in <some-dir>nuttx.

     tools/configure.sh c5471evm:<sub-dir>

  2. Download the latest buildroot package into <some-dir>

  3. unpack

  4. cd <some-dir>/buildroot

  5. cp boards/arm-defconfig .config

  6. make oldconfig

  7. make

  8. Make sure that the PATH variable includes the path to the newly built
     binaries.

Issues
^^^^^^

  Title:       UART RECONFIGURATION
  Description: UART re-configuration is untested and conditionally compiled out.
  Status:      Open
  Priority:    Medium.  ttyS1 is not configured, but not used; ttyS0 is configured
               by the bootloader

ARM/C5471-specific Configuration Options
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

        CONFIG_ARCH - Identifies the arch/ subdirectory.  This should
           be set to:

           CONFIG_ARCH=arm

        CONFIG_ARCH_family - For use in C code:

           CONFIG_ARCH_ARM=y

        CONFIG_ARCH_architecture - For use in C code:

           CONFIG_ARCH_ARM7TDMI=y

        CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory

           CONFIG_ARCH_CHIP=c5471

        CONFIG_ARCH_CHIP_name - For use in C code

           CONFIG_ARCH_CHIP_C5471

        CONFIG_ARCH_BOARD - Identifies the boards/ subdirectory and
           hence, the board that supports the particular chip or SoC.

           CONFIG_ARCH_BOARD=c5471evm (for the Spectrum Digital C5471 EVM)

        CONFIG_ARCH_BOARD_name - For use in C code

           CONFIG_ARCH_BOARD_C5471EVM (for the Spectrum Digital C5471 EVM)

        CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
           of delay loops

        CONFIG_ENDIAN_BIG - define if big endian (default is little
           endian)

        CONFIG_ROM_VECTORS - should be defined for the C5471 because the
           interrupt vectors are in ROM

        CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
           have LEDs

        CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
           stack. If defined, this symbol is the size of the interrupt
           stack in bytes.  If not defined, the user task stacks will be
          used during interrupt handling.

        CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions

  C5471 specific device driver settings

        CONFIG_SERIAL_IRDA_CONSOLE - selects the IRDA UART for the
           console ant ttys0 (default is the modem UART).
        CONFIG_UART_*_HWFLOWCONTROL - enables hardware flow control
        CONFIG_UART_*_RXBUFSIZE - Characters are buffered as received.
           This specific the size of the receive buffer
        CONFIG_UART_*_TXBUFSIZE - Characters are buffered before
           being sent.  This specific the size of the transmit buffer
        CONFIG_UART_*_BAUD - The configure BAUD of the UART.  Must be
        CONFIG_UART_*_BITS - The number of bits.  Must be either 7 or 8.
        CONFIG_UART_*_PARTIY - 0=no parity, 1=odd parity, 2=even parity
        CONFIG_UART_*_2STOP - Two stop bits

  C5471 Ethernet Driver settings

        CONFIG_C5471_NET_STATS
        CONFIG_C5471_PHY_AC101L or C5471_PHY_LU3X31T_T64
        CONFIG_C5471_AUTONEGOTIATION
        CONFIG_C5471_BASET100
        CONFIG_C5471_BASET10

Configurations
^^^^^^^^^^^^^^

Common Configuration Notes
--------------------------

  1. Each C5471 configuration is maintained in a sub-directory and
     can be selected as follow:

       tools/configure.sh c5471evm:<subdir>

     Where <subdir> is one of the configuration sub-directories described in
     the following paragraph.

  2. These configurations use the mconf-based configuration tool.  To
     change a configurations using that tool, you should:

     a. Build and install the kconfig-mconf tool.  See nuttx/README.txt
        see additional README.txt files in the NuttX tools repository.

     b. Execute 'make menuconfig' in nuttx/ in order to start the
        reconfiguration process.

  3. By default, all configurations assume the NuttX Buildroot toolchain
     under Linux (should work under Windows with Cygwin as well).  This
     is easily reconfigured:

        CONFIG_HOST_LINUX=y
        CONFIG_ARM_TOOLCHAIN_BUILDROOT=y

Configuration Sub-Directories
-----------------------------

  nettest

    This configuration enables networking using the c5471's built-in Ethernet
    interface.  It uses examples/nettest to exercise the TCP/IP network.

  nsh

    This configuration file builds NSH (examples/nsh) using the TELNET server
    front end

  httpd

    This configuration uses the tiny webserver for uIP.